Skip to content

Actions: Duet3D/RepRapFirmware

Actions

Auto-close blank templates

Actions

Loading...
Loading

Show workflow options

Create status badge

Loading
issues.yml
132 workflow runs
132 workflow runs

Filter by Event

Filter by Status

Filter by Branch

Filter by Actor

Different object cancellation behaviour when segmentation is used Auto-close blank templates #383: Issue #1194 opened by dc42
9s
9s
[FeatureRequest]: Add state.processing to the object model Auto-close blank templates #382: Issue #1193 opened by jaysuk
8s
8s
[Bug]: G1 at the end of stop.g locks up movement Auto-close blank templates #381: Issue #1192 opened by chrishamm
7s
7s
M571 not working in RRF 3.6.0 and 3.6.1 Auto-close blank templates #380: Issue #1191 opened by dc42
7s
7s
[Bug] Regression in motor reversion, when CAN latency causes a CAN-connected motor to overshoot Auto-close blank templates #379: Issue #1190 opened by droftarts
10s
10s
[FeatureRequest]: Act on incoming MQTT subscription Auto-close blank templates #378: Issue #1189 opened by olafvanschoten
6s
6s
Generate warnings instead of errors when moving outside limits in FFF mode Auto-close blank templates #377: Issue #1188 opened by chrishamm
8s
8s
[FeatureRequest]: Add support to control TMC2240's MOSFET charge/discharge rate Auto-close blank templates #376: Issue #1187 opened by Ataraxia-Mechanica
8s
8s
Tool failover Auto-close blank templates #375: Issue #1186 opened by T3P3
10s
10s
Feature request - Add the switch on the magnetic filament monitor as a virtual gpin port Auto-close blank templates #374: Issue #1185 opened by T3P3
8s
8s
Allow temperatures of individual drivers to be queried Auto-close blank templates #373: Issue #1184 opened by dc42
10s
10s
Improve driver temperature reporting when using TMC2240 drivers Auto-close blank templates #372: Issue #1183 opened by dc42
8s
8s
G20 and G21 affect interpretation of rotary axis angles Auto-close blank templates #371: Issue #1182 opened by dc42
9s
9s
Support structured local and global variables Auto-close blank templates #370: Issue #1181 opened by dc42
8s
8s
Support pressure advance changes without waiting for movement to stop Auto-close blank templates #369: Issue #1180 opened by dc42
15s
15s
Homing issue with RRF 3.6.0 and 3.6.1 on Duet2 Ethernet Auto-close blank templates #368: Issue #1179 opened by T3P3
13s
13s
Use gcode Line number to match gcode JSON requests to responses on UART and USB inputs Auto-close blank templates #367: Issue #1178 opened by T3P3
16s
16s
[Bug]: File G-codes can be queued while pausing in SBC mode Auto-close blank templates #366: Issue #1177 opened by chrishamm
14s
14s
M350 changes steps/mm of axes/extruders assigned to CAN-connected boards Auto-close blank templates #365: Issue #1176 opened by chrishamm
15s
15s
Incorrect extrusion amount when phase stepping enabled Auto-close blank templates #364: Issue #1175 opened by dc42
12s
12s
Object model field state.logLevel not updated after M929 S0 is used Auto-close blank templates #363: Issue #1174 opened by dc42
6s
6s
Expansion board reset after CAN debugging enabled Auto-close blank templates #362: Issue #1173 opened by dc42
7s
7s
Reduce minimum available speed to 0.1mm/min Auto-close blank templates #361: Issue #1172 opened by dc42
10s
10s
[FeatureRequest] Allow M302 to set higher retract temperature limit than extrusion Auto-close blank templates #360: Issue #1171 opened by droftarts
7m 4s
7m 4s
TOOL1LC running out of memory running RRF 3.6.1 Auto-close blank templates #359: Issue #1170 opened by dc42
10s
10s