Skip to content

Actions: Duet3D/RepRapFirmware

Actions

All workflows

Actions

Loading...
Loading

Showing runs from all workflows
159 workflow runs
159 workflow runs

Filter by Event

Filter by Status

Filter by Branch

Filter by Actor

Reduce minimum available speed to 0.1mm/min Auto-close blank templates #361: Issue #1172 opened by dc42
10s
10s
[FeatureRequest] Allow M302 to set higher retract temperature limit than extrusion Auto-close blank templates #360: Issue #1171 opened by droftarts
7m 4s
7m 4s
TOOL1LC running out of memory running RRF 3.6.1 Auto-close blank templates #359: Issue #1170 opened by dc42
10s
10s
M400 in pause.g breaks babystepping Auto-close blank templates #358: Issue #1169 opened by chrishamm
12s
12s
Build and and deploy firmware to dev Build and and deploy firmware to dev #40: Manually run by chrishamm
11m 51s v3-chrishamm
v3-chrishamm
11m 51s
G60 S1 + M26 Snnn + M24 results in print getting stuck in SBC mode Auto-close blank templates #357: Issue #1168 opened by chrishamm
10s
10s
[Bug]: resume.g not run when resuming with an unhomed axis Auto-close blank templates #356: Issue #1167 opened by AndyEveritt
10s
10s
Build and and deploy firmware to dev Build and and deploy firmware to dev #39: Manually run by dc42
13m 3s v3-chrishamm
v3-chrishamm
13m 3s
Build and and deploy firmware to dev Build and and deploy firmware to dev #38: Manually run by chrishamm
10m 45s v3-chrishamm
v3-chrishamm
10m 45s
Build and and deploy firmware to dev Build and and deploy firmware to dev #37: Manually run by chrishamm
13m 10s v3-chrishamm
v3-chrishamm
13m 10s
Movement abort when phase stepping enabled during a print Auto-close blank templates #355: Issue #1166 opened by dc42
10s
10s
Job hangs and crashes with out of memory error when phase stepping enabled Auto-close blank templates #354: Issue #1165 opened by dc42
10s
10s
[FeatureRequest]: Add exec meta gcode to run arbitrary gcode strings Auto-close blank templates #353: Issue #1164 opened by AndyEveritt
9s
9s
Expansion board CanClock task stack overflow when debugging enabled Auto-close blank templates #352: Issue #1163 opened by dc42
8s
8s
Extruder positions sometimes incorrect after tool change Auto-close blank templates #351: Issue #1162 opened by dc42
8s
8s
M486 object cancellation causing XY skipping and/or extra moves Auto-close blank templates #350: Issue #1161 opened by droftarts
10s
10s
Add M500 P68 parameter to store G68 parameters in config-override.g Auto-close blank templates #349: Issue #1160 opened by dc42
8s
8s
Add G68 rotation to resurrect.g Auto-close blank templates #348: Issue #1159 opened by dc42
10s
10s
Some moves fail to complete when using phase stepping and M400 Auto-close blank templates #347: Issue #1158 opened by dc42
10s
10s
Release 3.6.1 Upload prerelease assets #12: Release 3.6.1 published by dc42
1s
1s
Release 3.6.1 Upload release assets #25: Release 3.6.1 published by dc42
35s
35s
Add support for SBC protocol over USB Auto-close blank templates #346: Issue #1157 opened by T3P3
13s
13s
Add a second CDC channel in TinyUSB Auto-close blank templates #345: Issue #1156 opened by T3P3
9s
9s
[Bug]: M118 P2 doesn't send message to PanelDue Auto-close blank templates #344: Issue #1155 opened by chrishamm
6s
6s
Tool position incorrect after simulating Auto-close blank templates #343: Issue #1154 opened by dc42
9s
9s