Oled chip

[smashthony]

Hi I just finished installed my oled chip but when I press on it blinks like a greenish yellow 3 times and on the 3rd in it’s longer then it flashes red once then the same process over and over help pls

[sthetix]

Most of the time it is doe to the dat0 losing connection.. Please check it again

…

On Tue, May 17, 2022, 09:06 smashthony ***@***.***> wrote: Hi I just finished installed my oled chip but when I press on it blinks like a greenish yellow 3 times and on the 3rd in it’s longer then it flashes red once then the same process over and over help pls — Reply to this email directly, view it on GitHub <#7>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFJ23D2OLCDUTDVLAHRBJMLVKL5KBANCNFSM5WDKK5DA> . You are receiving this because you are subscribed to this thread.Message ID: ***@***.***>

[smashthony]

How do I fix that I need help please

[sthetix]

Better wait for my upcoming short video today.

…

On Tue, May 17, 2022, 09:40 smashthony ***@***.***> wrote: How do I fix that I need help please — Reply to this email directly, view it on GitHub <#7 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFJ23D2A2ZH2T4BMHNQTO2LVKMBKVANCNFSM5WDKK5DA> . You are receiving this because you commented.Message ID: ***@***.***>

[smashthony]

How long until its comes out in trying to get this done before I go to bed 😭😭😭

[sthetix]

Today means in several hours upto 12 hours. It's 9.45 am here. I mean time u need to check the soldering points diode values. Just like I did in the installation video

…

On Tue, May 17, 2022, 09:45 smashthony ***@***.***> wrote: How long until its comes out in trying to get this done before I go to bed 😭😭😭 — Reply to this email directly, view it on GitHub <#7 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFJ23D7VGCX2LKZMC4455UTVKMB2ZANCNFSM5WDKK5DA> . You are receiving this because you commented.Message ID: ***@***.***>

[smashthony]

Also the RST point shows 0 on my multimeter

[sthetix]

Rst 0 is ok.. Dat0 (C) should not be 0.

…

On Tue, May 17, 2022, 09:47 smashthony ***@***.***> wrote: Also the RST point shows 0 on my multimeter — Reply to this email directly, view it on GitHub <#7 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFJ23D7Z256DO5WDPS6U4VDVKMCDVANCNFSM5WDKK5DA> . You are receiving this because you commented.Message ID: ***@***.***>

[smashthony]

Just checked all the points it was the A point it had a 0

[sthetix]

That is causing the issue. Maybe the resistor of that A point is damaged. Please check that

…

On Tue, May 17, 2022, 10:23 smashthony ***@***.***> wrote: Just checked all the points it was the A point it had a 0 — Reply to this email directly, view it on GitHub <#7 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFJ23DZTIF7IJYOMJ76WYHLVKMGKVANCNFSM5WDKK5DA> . You are receiving this because you commented.Message ID: ***@***.***>

[smashthony]

It's showing a value now but I'm still having the light problem

[sthetix]

The resistor should be 4.7k ohm..remove the chip wires (3.3v, rst, and gnd), and see if you can boot ur console normally

…

On Tue, May 17, 2022, 10:26 smashthony ***@***.***> wrote: It's showing a value now but I'm still having the light problem — Reply to this email directly, view it on GitHub <#7 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFJ23D7Y3RQ24GLRILLETBTVKMGVLANCNFSM5WDKK5DA> . You are receiving this because you commented.Message ID: ***@***.***>

[smashthony]

Just checked I can boot

[sthetix]

Then u need to recheck the dat0 connection or the cpu flex ribbon pads

…

On Tue, May 17, 2022, 10:32 smashthony ***@***.***> wrote: Just checked I can boot — Reply to this email directly, view it on GitHub <#7 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFJ23D2OQMUYRQOVZS4ACSTVKMHMHANCNFSM5WDKK5DA> . You are receiving this because you commented.Message ID: ***@***.***>

[smashthony]

I cant*

[sthetix]

No boot? Check the résistance value on the A point. It should have 4.7k.ohm. If more than that, u need to replace the resistor.

…

On Tue, May 17, 2022, 10:33 smashthony ***@***.***> wrote: I cant* — Reply to this email directly, view it on GitHub <#7 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFJ23D7EI4IWIABP3PEIN3DVKMHQZANCNFSM5WDKK5DA> . You are receiving this because you commented.Message ID: ***@***.***>