Napalm net.cli race condition #55332
Description
Description of Issue
If you run 2 parallel net.cli commands, the output can get mixed up. There is also a change it can break the napalm proxy-minion if the wrong process reads consumes the prompt.
In the example below I run the following two loops:
while [ true ]; do salt 'mlnx1.switch' net.cli "show version"; done
while [ true ]; do salt 'mlnx1.switch' net.cli "show int status"; done
This quickly reproduces the issue, but a more common, real world example is when the minion grains gets refreshed at the same time as applying a state.
In the above example, you would expect the first command to produce the following output:
Product name: Onyx
Product release: 3.8.2004
Build ID: #1-dev
Build date: 2019-09-23 14:19:47
Target arch: x86_64
Target hw: x86_64
Built by: jenkins@7ae5fd122b61
Version summary: X86_64 3.8.2004 2019-09-23 14:19:47 x86_64
Product model: x86onie
Host ID: B8599F0E752C
System serial num: MT1917K00431
System UUID: 946e383c-69ed-11e9-8000-b8599f63da40
Uptime: 7d 23h 1m 28.512s
CPU load averages: 3.01 / 3.05 / 3.07
Number of CPUs: 4
System memory: 2628 MB used / 5175 MB free / 7803 MB total
Swap: 0 MB used / 0 MB free / 0 MB total
And the 2nd command:
--------------------------------------------------------------------------------------------------------------------------------
Port Operational state Admin Speed Description
--------------------------------------------------------------------------------------------------------------------------------
mgmt0 Up Enabled 1000Mb/s (auto) -
Eth1/1 Down Enabled Unknown -
Eth1/2 Down Enabled Unknown -
Eth1/3 Down Enabled Unknown -
Eth1/4 Down Enabled Unknown -
Eth1/5 Down Enabled Unknown -
Eth1/6 Down Enabled Unknown -
Eth1/7 Down Enabled Unknown -
Eth1/8 Down Enabled Unknown -
Eth1/9 Down Enabled Unknown -
Eth1/10 Down Enabled Unknown -
Eth1/11 Down Enabled Unknown -
Eth1/12 Down Enabled Unknown -
Eth1/13 Down Enabled Unknown -
Eth1/14 Down Enabled Unknown -
Eth1/15 Down Enabled Unknown -
Eth1/16 Down Enabled Unknown -
Eth1/17 Down Enabled Unknown -
Eth1/18 Down Enabled Unknown -
Eth1/19 Up Enabled 40G -
Eth1/20 Up Enabled 40G -
Eth1/21 Down Enabled Unknown -
Eth1/22 Down Enabled Unknown -
In the file attached, I show an example of the output of the proxy-minion in debug mode when the two commands are getting merged.
- The first command is alloctaed JID
20191115154146169012. - The 2nd command is allocated JID:
20191115154146711930
20191115154146169012 returns:
[DEBUG ] minion return: {u'fun_args': [u'show version'], u'jid': u'20191115154146169012', u'return': {u'comment': u'', u'result': True, u'out': {u'show version':
u'us\n--------------------------------------------------------------------------------------------------------------------------------\n\nPort Operational state Admin Speed
Description \n--------------------------------------------------------------------------------------------------------------------------------\nmgmt0 Up
Enabled 1000Mb/s (auto) -\nEth1/1 Down Enabled Unknown - \nEth1/2 Down
Enabled Unknown - \nEth1/3 Down Enabled Unknown - \nEth1/
4 Down Enabled Unknown - \nEth1/5 Down Enabled
Unknown - \nEth1/12 Down Enabled Unknown - \nEth1/13 Down
Enabled Unknown - \nEth1/14 Down Enabled Unknown - \nEth1/
15 Down Enabled Unknown - \nEth1/16 Down Enabled
Unknown - \nEth1/17 Down Enabled Unknown - \nEth1/18 Down
Enabled Unknown - \n\n'}}, u'retcode': 0, u'success': True, u'fun': u'net.cli'}
20191115154146711930 returns:
[DEBUG ] minion return: {u'fun_args': [u'show int status'], u'jid': u'20191115154146711930', u'return': {u'comment': u'', u'result': True, u'out': {u'show int status': u'
Down Enabled Unknown - \nEth1/7 Down Enabled
Unknown - \nEth1/8 Down Enabled Unknown - \nEth1/9 Down
Enabled Unknown - \nEth1/10 Down Enabled Unknown - \nEth1/
11 Down Enabled Unknown - \nEth1/19 Up Enabled
40G - \nEth1/20 Up Enabled 40G - \nEth1/21 Down
Enabled Unknown - \nEth1/22 Down Enabled Unknown - \n'}},
u'retcode': 0, u'success': True, u'fun': u'net.cli'}
Versions Report
# salt --versions-report
Salt Version:
Salt: 2019.2.2
Dependency Versions:
cffi: 1.12.3
cherrypy: unknown
dateutil: 2.7.2
docker-py: 3.5.0
gitdb: 2.0.5
gitpython: 2.1.11
ioflo: Not Installed
Jinja2: 2.9.6
libgit2: Not Installed
libnacl: 1.6.1
M2Crypto: 0.31.0
Mako: 1.0.12
msgpack-pure: Not Installed
msgpack-python: 0.5.6
mysql-python: 1.2.5
pycparser: 2.19
pycrypto: 2.6.1
pycryptodome: 3.7.3
pygit2: Not Installed
Python: 2.7.5 (default, Aug 7 2019, 00:51:29)
python-gnupg: Not Installed
PyYAML: 3.11
PyZMQ: 15.3.0
RAET: Not Installed
smmap: 2.0.5
timelib: Not Installed
Tornado: 4.2.1
ZMQ: 4.1.4
System Versions:
dist: centos 7.7.1908 Core
locale: UTF-8
machine: x86_64
release: 3.10.0-1062.1.2.el7.x86_64
system: Linux
version: CentOS Linux 7.7.1908 Core
Using the onyx napalm driver (https://github.com/napalm-automation-community/napalm-onyx), but I don't think this should make a difference?