diff --git a/docs/delta/7/7.md b/docs/delta/7/7.md index 3a77216..cf743a4 100644 --- a/docs/delta/7/7.md +++ b/docs/delta/7/7.md @@ -4,7 +4,7 @@ title: Line connection ## 0. Line connection warning -!!! warning "warning" +!!! warning "Warning" Do not operate with electricity on during the wiring process, as it will cause damage to you and your machine. @@ -77,18 +77,18 @@ title: Line connection ### Assembly process -1.Snap the hot bed into the groove of the rear hot bed baffle, perform the wire management using cable ties to sort out the wires and cut off the excess parts of the cable ties, as shown in the picture. +1. Snap the hot bed into the groove of the rear hot bed baffle. Perform the wire management using cable ties to sort out the wires and cut off the excess parts of the cable ties, as shown in the picture. ![image.webp](55.webp){.img1} -2.Thread the wire through the thread hole of the lower foot decoration and pull it out from above, then thread it into the thread hole of the lower foot decoration and pull it out from the stepper motor, as shown in the figure. +2. Thread the wire through the thread hole of the lower foot decoration and pull it out from above, then thread it into the thread hole of the lower foot decoration and pull it out from the stepper motor, as shown in the figure. ![image.webp](11.webp){.img1} ![image.webp](12.webp){.img1} -3.Use the 3030 profile end cap to snap the wire into the long aluminium profile, as shown in the picture. +3. Use the 3030 profile end cap to snap the wire into the long aluminium profile, as shown in the picture. ![image.webp](13.webp){.img1} ![image.webp](14.webp){.img1} -4.Use the 2020 profile end cap to snap the wire into the long aluminium profile, as shown in the picture. +4. Use the 2020 profile end cap to snap the wire into the long aluminium profile, as shown in the picture. ![image.webp](15.webp){.img1} ![image.webp](16.webp){.img1} ![image.webp](17.webp){.img1} @@ -118,46 +118,46 @@ title: Line connection ### Assembly process -1.Buckle the upper and lower flanges with the middle flanges, note that this structure is a mortise and tenon structure, and the circular buckles need to be all snapped into the circular grooves, as shown in the figure. +1. Buckle the upper and lower flanges with the middle flanges, note that this structure is a mortise and tenon structure, and the circular buckles need to be all snapped into the circular grooves, as shown in the figure. ![image.webp](18.webp){.img1} ![image.webp](19.webp){.img1} ![image.webp](20.webp){.img1} -2.Use the same method to buckle and put it together the other 2 as shown in the picture. +2. Use the same method to buckle and put it together the other 2 as shown in the picture. ![image.webp](21.webp){.img1} -3.Buckle into the long aluminium profile, as shown in the figure. +3. Buckle into the long aluminium profile, as shown in the figure. ![image.webp](22.webp){.img1} ![image.webp](23.webp){.img1} -4.Screw the M4*10 cap head screw into the drop-in t-nut (30 - M4), but do not tighten, just screw it on, as shown in the picture. +4. Screw the M4*10 cap head screw into the t-nut (30 - M4), but do not tighten. Just screw it on, as shown in the picture. ![image.webp](24.webp){.img1} -5.Put the screw into the snap slot of the long aluminum profile, slide the screw down to snap into the groove of the upper and lower flanges, and screw the screw, as shown in the picture. +5. Put the screw into the snap slot of the long aluminum profile. Slide the screw down to snap into the groove of the upper and lower flanges, and screw the screw, as shown in the picture. ![image.webp](25.webp){.img1} ![image.webp](26.webp){.img1} ![image.webp](27.webp){.img1} ![image.webp](28.webp){.img1} ![image.webp](29.webp){.img1} -!!! warning "warning" - Pay attention to the position of the drop-in t-nut (type 30-M4), which should be stuck in the groove of the long profile, and should not be tightened too tightly to avoid damaging the printed part. +!!! warning "Warning" + Pay attention to the position of the t-nut (type 30-M4), which should be stuck in the groove of the long profile, and should not be tightened too tightly to avoid damaging the printed part. ![image.webp](30.webp){.img1} -6.In the same way, put the screw into the card slot of the long aluminum profile, slide the screw up to make it snap into the groove of the middle edge, and screw the screw, as shown in the figure. +6. In the same way, put the screw into the card slot of the long aluminum profile, and slide the screw up to make it snap into the groove of the middle edge, and then tighten the screw, as shown in the figure. ![image.webp](31.webp){.img1} !!! warning "warning" Pay attention to the position of the drop-in t-nut (type 30-M4), which should be stuck in the groove of the long profile, and should not be tightened too tightly to avoid damaging the printed part. ![image.webp](32.webp){.img1} -7.The installation method of the other two screws is the same, as shown in the picture. +7. The installation method of the other two screws is the same, as shown in the picture. ![image.webp](33.webp){.img1} -8.The installation method on the other side is the same, as shown in the picture. +8. The installation method on the other side is the same, as shown in the picture. ![image.webp](34.webp){.img1} -9.The other two sets of installations, are the same as shown in the picture. +9. The other two sets of installations, are the same as shown in the picture. ![image.webp](35.webp){.img1} !!! info "See color scheme" @@ -184,12 +184,12 @@ title: Line connection ### Assembly process -1.Screw four M3*14 cap head screws through the 4010 cooling fan to the fan bracket, do not tighten too tightly to avoid screwing the print, as shown in the picture. +1. Screw four M3*14 cap head screws through the 4010 cooling fan to the fan bracket, but do not tighten too tightly to avoid damaging the printed part, as shown in the picture. ![image.webp](36.webp){.img1} ![image.webp](37.webp){.img1} ![image.webp](38.webp){.img1} -2.Fix the fan bracket to the motherboard of the lower chassis as shown in the figure. +2. Secure the fan bracket to the motherboard of the lower chassis as shown in the figure. ![image.webp](39.webp){.img1} ## 5.Cover assembly @@ -221,13 +221,13 @@ title: Line connection ### Assembly process -1.Cut a short 90mm length of PTFE tube, and insert it into the base plate connector, as shown in the figure. +1. Cut a short 90mm length of PTFE tube, and insert it into the base plate connector, as shown in the figure. ![image.webp](40.webp){.img1} ![image.webp](41.webp){.img1} ![image.webp](42.webp){.img1} ![image.webp](43.webp){.img1} -2.Use a soldering iron to press the three heat inserts into the cover plate connector as shown. +2. Use a soldering iron to press the three heat inserts into the cover plate connector as shown. ![image.webp](44.webp){.img1} ![image.webp](45.webp){.img1} @@ -236,17 +236,17 @@ title: Line connection ![image.webp](47.webp){.img1} ![image.webp](48.webp){.img1} -4.Put the above assembled parts on the top of the printer and the PTFE tube passes through the cover plate connector as shown in the picture. +4. Put the above assembled parts on the top of the printer. The PTFE tube passes through the cover plate connector as shown in the picture. ![image.webp](49.webp){.img1} -5.Put on the last cover plate and use M3*8 countersunk screws to lock the cover plate with the cover plate connector, as shown in the picture. +5. Put on the last cover plate and use M3*8 countersunk screws to lock the cover plate with the cover plate connector, as shown in the picture. ![image.webp](50.webp){.img1} -6.Use M3*8 countersunk screws to lock all cover plates as shown. +6. Use M3*8 countersunk screws to lock all cover plates as shown. ![image.webp](51.webp){.img1} ![image.webp](52.webp){.img1} -7.The filament holder can be placed on the side or top to set the filament and print happily. +7. The filament holder can be placed on the side or top to set the filament and print happily. ![image.webp](53.webp){.img1} ![image.webp](54.webp){.img1}