r0.2 Errata

[joshajohnson]

This issue will document any errata / areas for improvement for future versions.

Note, whilst the board has passed the smoke test, it has not been fully brought up so this list is subject to growing.

• USB CC pulldown resistors are in the way of the SD card, card can still be inserted but is less than ideal.
• PD37+- diff pair is not routed correctly under the SD card.
• C510 is too close to C514
• C14 and R2 should have their positions swapped in layout.

[giggiu16]

Hey @joshajohnson! For a very big coincidence I assembled the r0.2 simultaneously with you! 😄
Just had the time to perform (a successful!) smoke test and an initial JTAG chain scan (w/ openocd& ftdi/jlink) but no devices were discovered. Do you managed to program the ECP5?
Thank you!

[joshajohnson]

Hey @giggiu16, I was able to program both of the r0.2 boards I assembled. I used ecpprog with a FT232.

Let me know how you go / if there is anything I can do to help!

[giggiu16]

@joshajohnson -- thank you so much!
Just changed to FT232 + ecpprog combination and...

init..
IDCODE: 0x21111043 (LFE5U-12)
ECP5 Status Register: 0x06400000
flash ID: 0xEF 0x40 0x18 0x00
Bye.

I confirm also that the bootloader is working correclty even on r0.2:

Found DFU: [1d50:614b] ver=0005, devnum=2, cfg=1, intf=0, path="20-4", alt=2, name="Bootloader", serial="e46050640f354126"
Found DFU: [1d50:614b] ver=0005, devnum=2, cfg=1, intf=0, path="20-4", alt=1, name="RISC-V firmware", serial="e46050640f354126"
Found DFU: [1d50:614b] ver=0005, devnum=2, cfg=1, intf=0, path="20-4", alt=0, name="ECP5 bitstream", serial="e46050640f354126"

Thank you so much!

[joshajohnson]

@giggiu16 Nice work! If you are in the position to share what you are using it for I'd be keen to hear, otherwise have fun!

[giggiu16]

@joshajohnson for sure: no specific use case in mind for now. I'll use your board to continue learning FPGA programming, I didn't wanted to be limitated in GPIO pins too much comparing other "low-cost" solutions. I like also assemblying electronic prototypes and I used your board as first BGA assembly test 😄. Next 2 boards in queue, and one is with the 25F variant 😉.

[joshajohnson]

@giggiu16 Awesome!

One thing I should say is that the 12F and the 25F are the same silicon, but with a different IDCODEs. If you use the open tools you'll be able to use all 25K LUTs on the 12F!

[amitvasudevan]

Hi @joshajohnson and @giggiu16! Nice work on the ECP5-mini board. How did you solder the BGA on the PCB? Did you just use a hot air gun/flux combo or was it something more sophisticated? Thanks!

[joshajohnson]

Hi @amitvasudevan, I'd suggest reflowing it along with the rest of the components. You can do it with hot air but getting even heating is a bit more challenging.

[joshajohnson]

Closed on accident

[amitvasudevan]

Thanks for the response @joshajohnson !

I am a newbie when it comes down to soldering so please forgive my naive questions below :)

• From what I read up on reflow seems like a three step process: (a) obtain stencil for PCB, (b) apply solder paste over stencil, and (c) place the pcb in the reflow oven. Correct?
• I am planning to order the PCB via OSHPark; do they provide stencils?
• Also I noticed that your PCB design has components soldered on both the top and bottom. How does that work in the reflow oven? Do you do one side first and then the other? If so, won't the already soldered components on the side down reflow and dislodge?
• I am planning on assembling this at home and was looking for reflow ovens on amazon and it seems like there are units available for ~$250 or so. Is there a specific unit you would recommend? Also I am guessing the temperature will depend on the solder paste being used correct?

Thanks for your time and help! Can't wait to get started...

[joshajohnson]

• Correct

• OSHStencils (no relation to OSHPark) provide stencils.

• Yes, you reflow the bottom side then the top side. There is no issues with the bottom side falling off on the second time through the oven as they are all lightweight.

• Esden has a good summary of modifying an oven here. I have a T962 (not T962A) and it's okay, but I'd buy the higher end option next time.

• Yes you will want to play around with a few boards / temperature profiles before throwing your first actual board in there to see what works best.

[amitvasudevan]

Thanks @joshajohnson! This is very helpful. I looked at the T962/A modifications and found the thermocouple interface board is no longer available from 1bitsquared. Is that an important component or can I still work without it?