I tried using two different firmware versions:
firmware 1.1.1 bug fixes.bin
lightclock 1.1 - sun and moon.bin
and also tested on NodeMCU and Wemos boards — the result is the same. I configure the settings in access point mode, press “Save and Restart,” the ESP restarts, but it goes back into access point mode again, as if the settings were not saved.
11:56:52.666 -> clockmode 2
11:56:52.666 ->
11:56:52.666 ->
11:56:52.666 -> Startup
11:56:55.201 -> scan done
11:56:55.201 -> 6Networks found
11:56:55.201 -> 1: ALHN-572C (-78)*
11:56:55.234 -> 2: DIRECT-Tx-EPSON-L3160 Series (-83)*
11:56:55.234 -> 3: SmartHome (-52)*
11:56:55.234 -> 4: www.etaxi.lv (-74)*
11:56:55.234 -> 5: China_Flash (-76)*
11:56:55.267 -> 6: HUAWEI-B525-B8DF (-80)*
11:56:55.267 ->
11:56:55.629 -> USP Server started
11:56:55.629 -> Access point started with name The Light Clock
11:56:55.629 -> Access point started with name The Light Clock
11:56:55.629 ->
11:56:55.629 -> WiFi connected
11:56:55.629 -> 192.168.4.1
11:56:55.629 -> Web server started
11:56:56.618 -> clockmode 2
11:57:09.305 -> Sending webHandleConfig
11:57:11.543 -> Sending webHandleConfig
11:57:11.703 -> Sending CSS
11:57:11.902 -> Sending webHandleConfig
11:57:12.100 -> Sending webHandleConfig
11:57:18.460 -> Sending webHandlePassword
11:57:18.498 -> SmartHome
11:57:18.498 ->
11:57:18.498 -> clearing old ssid.
11:57:18.689 -> writing eeprom ssid.
11:57:18.689 -> SmartHome
11:57:19.848 -> Sending CSS
11:57:19.946 -> Sending webHandleConfig
11:57:20.081 -> Sending webHandleConfig
11:57:26.775 -> Sending webHandleTimeZoneSetup
11:57:26.840 -> clearing old pass.
11:57:27.038 -> fjdOkdwo888
11:57:27.038 ->
11:57:27.038 -> writing eeprom pass.
11:57:27.038 -> fjdOkdwo888
11:57:28.225 -> Sending CSS
11:57:28.356 -> Sending webHandleConfig
11:57:28.488 -> Sending webHandleConfig
11:57:47.821 -> Sending webHandleConfigSave
11:57:48.834 -> Settings written, restarting!
11:57:48.834 ->
11:57:48.834 -> ets Jan 8 2013,rst cause:2, boot mode:(3,7)
11:57:48.834 ->
11:57:48.834 -> load 0x4010f000, len 1384, room 16
11:57:48.834 -> tail 8
11:57:48.834 -> chksum 0x2d
11:57:48.834 -> csum 0x2d
11:57:48.834 -> v09f0c112
11:57:48.834 -> ~ld
11:57:51.694 -> clockmode 2
11:57:51.725 ->
11:57:51.725 ->
11:57:51.725 -> Startup
11:57:54.100 -> scan done
11:57:54.100 -> 7Networks found
11:57:54.100 -> 1: ALHN-572C (-80)*
11:57:54.100 -> 2: LGTVKarps (-76)*
11:57:54.100 -> 3: DIRECT-Tx-EPSON-L3160 Series (-80)*
11:57:54.133 -> 4: ALHN-B2DF (-81)*
11:57:54.133 -> 5: SmartHome (-50)*
11:57:54.133 -> 6: www.etaxi.lv (-76)*
11:57:54.166 -> 7: China_Flash (-75)*
11:57:54.166 ->
11:57:54.532 -> USP Server started
11:57:54.532 -> Access point started with name The Light Clock
11:57:54.532 -> Access point started with name The Light Clock
11:57:54.532 ->
11:57:54.532 -> WiFi connected
11:57:54.532 -> 192.168.4.1
11:57:54.532 -> Web server started
11:57:55.864 -> clockmode 2
I tried using two different firmware versions:
firmware 1.1.1 bug fixes.bin
lightclock 1.1 - sun and moon.bin
and also tested on NodeMCU and Wemos boards — the result is the same. I configure the settings in access point mode, press “Save and Restart,” the ESP restarts, but it goes back into access point mode again, as if the settings were not saved.