Don't have nuts

[hasecilu]

The STEMFIE system consists of several components as fasteners, shafts, gears, etc.

I think it's beneficial to have more components available on the workbench.

https://get.stemfie.org/

---

Beams

• Beams - Angled - T-shaped Symmetric - Square Ends
• Beams - Angled - U-shaped Symmetric - Square Ends
• Beams - Straight - Box-Section - Square Ends/
• Beams - Straight - Standard - Square Ends
• Beams - Straight - Standard - Square Threaded Ends - Double-Ended #16

Braces

• Braces - Angled - 90 Degrees - Asymmetric - Round Ends
• Braces - Angled - 90 Degrees - Symmetric - Round Ends
• Braces - Cross - Standard - Symmetric - Round Ends
• Braces - Straight - Slotted - Both Ends - Round Ends
• Braces - Straight - Slotted - Centered - Round Ends
• Braces - Straight - Slotted - Full Length - Round Ends
• Braces - Straight - Slotted - Sequential - Round Ends
• Braces - Straight - Slotted - Single End - Round Ends
• Braces - Straight - Standard - Round Ends

Connectors

• 1 way
• 2 ways 90°
• 2 ways 180°
• 3 ways
• 4 ways

Fasteners

Nuts

Cam-locking

• Open - https://get.stemfie.org/Fasteners%20-%20Nuts%20-%20Cam-Locking%20-%20Open/

Threaded

• Barrel through hole center - https://get.stemfie.org/Fasteners%20-%20Nuts%20-%20Threaded%20-%20Barrel%20-%20Symmetric%20-%20Through-Hole%20Center%20-%20Threaded%20Double-Ended/
• Open - https://get.stemfie.org/Fasteners%20-%20Nuts%20-%20Threaded%20-%20Open/
• Barrel threaded center - https://get.stemfie.org/Fasteners%20-%20Nuts%20-%20Threaded%20-%20Barrel%20-%20Symmetric%20-%20Threaded%20Center-Double-Ended/
• Cap nuts - <https://get.stemfie.org/Fasteners%20-%20Nuts%20-%20Threaded%20-
  %20Cap%20Nuts/>
• Adhesive mount - https://get.stemfie.org/Fasteners%20-%20Nuts%20-%20Threaded%20-%20Adhesive-Mount/

Pins

• Spring pins locating unidirectional - https://get.stemfie.org/Fasteners%20-%20Pins%20-%20Spring%20Pin%20-%20Locating%20-%20Asymmetric%20-%20Unidirectional/
• Spring pin inner - https://get.stemfie.org/Fasteners%20-%20Pins%20-%20Spring%20Pin%20-%20Inner/
• Cam locking - https://get.stemfie.org/Fasteners%20-%20Pins%20-%20Cam-Locking%20-%20Rounded%20Head/
• Spring pin locating bidirectional - https://get.stemfie.org/Fasteners%20-%20Pins%20-%20Spring%20Pin%20-%20Locating%20-%20Symmetric%20-%20Bidirectional/

Screws

• Fully threaded RHD- https://get.stemfie.org/Fasteners%20-%20Screws%20-%20Fully%20Threaded%20-%20Rounded%20Head/
• Shoulder screws RHD - https://get.stemfie.org/Fasteners%20-%20Shoulder%20Screws%20-%20Rounded%20Head/
• Fully threaded STEMFIE HEAD - https://get.stemfie.org/Fasteners%20-%20Screws%20-%20Fully%20Threaded%20-%20STEMFIE%20Head/

Spacers

• Bud - Free - https://get.stemfie.org/Fasteners%20-%20Spacers%20-%20BUD%20-%20Free/
• Fixed - https://get.stemfie.org/Fasteners%20-%20Spacers%20-%20Fixed/
• Free - https://get.stemfie.org/Fasteners%20-%20Spacers%20-%20Free/
• Free - Adhesive mount https://get.stemfie.org/Fasteners%20-%20Spacers%20-%20Free%20-%20Adhesive-Mount/

Threaded rods

• Fully threaded - https://get.stemfie.org/Fasteners%20-%20Threaded%20Rods%20-%20Fully%20Threaded/

Washers

• Fasteners - Washers - Fixed #18
• Fasteners - Washers - Free #17

Plates

• Triangular plate
• Square plate - in reality we have rectangular plate
• Hexagonal plate

Shafts

• Plain - https://get.stemfie.org/Shafts%20-%20Plain/
• Indexing - https://get.stemfie.org/Shafts%20-%20Indexing/

Springs

• Rotor - https://get.stemfie.org/Springs%20-%20Rotor/

Tools

• Driver Nut - https://www.stemfie.org/parts?view=article&id=161:driver-nut-spn-tol-0034&catid=40
• Driver Screw Nut - https://www.stemfie.org/parts?view=article&id=159:driver-screw-nut-spn-tol-0001&catid=40
• Driver Nut Screw RHD - https://www.stemfie.org/parts?view=article&id=181:spn-tol-0035&catid=40
• Spanner Nut - https://www.stemfie.org/parts?view=article&id=160:spanner-nut-spn-tol-0004&catid=40

[Stemfie3D]

I fully agree. The complete set of CAD files for adding new parts to the workbench can be fetched from get.stemfie.org.

[hasecilu]

If there is no response I could step as maintainer in my fork... ideally parts would be parametrically created, but for the time being could make a command to download from cloud, any help is appreciated.