PickAndPlaceFileConverterRev2/file format.txt at main · AlexanderPeters/PickAndPlaceFileConverterRev2 · GitHub

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Example lines to show assembled structure of a line in the .NC file.
N0001/0M000X+00000Y+00000Z0000W000U00MH+000;
N0002/0M000X+00000Y+00000Z0000W000U00MH+000;
N0003/0M000X+00000Y+00000Z0000W000U00MH+000;
// Program continues as follows with alternate feeder data. Default for each value is 000 (no alternate selected).
S01Z000G000,000,000,000 // Five positions for five digit number
.
.
.
S40Z000G000,000,000,000 // Each position left -> right then up -> down
*			// sequentially increases the feeder index from 1 -> 200
			// and the correcponding value 000 -> 999
			// is the alternate set number
			// see page 5-43 of operation manual
[Note 5 * 40 = 200 feeder slots, hence 40 lines with 5 3 digit nums]

Breakdown of each line as idividual items veritcally
[range of vals]
(units of vals)
"Comment"

N
lineNum [0001 -> 2000]
/
skip [0 -> 9]
M
mCode [000 -> 999]
X
xDist [-99999 -> +99999] (mm/100)
Y
yDist [-99999 -> +99999] (mm/100)
Z
unknown value [0 only?] "Unknown function. Maybe for extra feeders on other machine models?"
-Yes anything other than 0 is interpreted weirdly. i.e. multiplited by five and used as the head number
-e.x. 5 is a head number of 25 and 9 is a head number of 45. The screen can't even display these values properly.
feederNum/headNum [001 -> 200] "Feeders 1->200 on Head 1"
		  [201 -> 400] "Feeders 1->200 on Head 2"
                  [401 -> 600] "Feeders 1->200 on Head 3"
// Feeders 141 -> 150 for each head not available for selection on this machine
W
angle [000 -> 359]
U
unused axis? [00 -> 99]????? "Was always U00 in every file example file I looked at."
	-Axis used on other machine models? Conveyor width adjustment axis?
	-Best current guess is this is unused by the machine and it can't interpret it.
		-Checked with some values, but was unable to fully confirm this is the case.
		-Still until future refference and it is needed I'm ignoring this.
MH
mountHeight [-999 -> 999]
;
comment [10 alphaNumeric char]


M Codes (Done enough, there are likely many others, aswell as combinations of multiple functions
		but, not important enough to worry about for now.)


M000 -> All special commands 0
Special commands if single var and all other field = 0
M006 -> Bad Mark = 1
M007 -> Bad Mark = 2
M801 -> Alignment Mark = 1
M802 -> Alignment Mark = 2
M000 -> Repeat = 0
M901 -> Repeat = 1
M902 -> Repeat = 2
M911 -> Repeat = 3
M912 -> Repeat = 4
M921 -> Repeat = 5
M922 -> Repeat = 6
M931 -> Repeat = 7
M932 -> Repeat = 8
Dispense options 1 and 2 require mount to be set to 0
M000 -> Mount/Dispense both 0
M002 -> Mount = 1, Dispense = 0
M004 -> Mount = 0, Dispense = 1
M005 -> Mount = 0, Dispense = 2


Other company only used
M000
M002
M801